Відео

I got a 2003 Ford escape overdrive light is flashing it won't let me go in reverse into a dust how do you fix it

Warning! People please do not touch capacitor it's holds a charge/voltage even after being unplugged!

you know what you are doing you are the man...

I’m so far away. I wish I was closer.

What tool did you use to actually replace the seal tho?

Clay, you and your family are great Americans. You are showing us how American has changed against the people who work and care for their families. The country is now worried for the corporations. Your videos show how ingenious you are when finding solutions for regular people's cars. Yet the country does not help the ones who hold it together. May our thoughts and acts of kindness find it's way to you and your family. I thank you for all the help you provide in your repair videos.

I mean its a 6 hour ride for you, but we got whole house AC a few years ago. I assume the window unit sitting in the basement still works.

Do you have an Aging and Disability Resource Center there in your area? If so they can be a great help in advocating and helping with his needs . They will give a caseworker to help with everything.

Clay.....you can try to contact your Congressman !!! I've heard of some good things they have done for individual constituents.

Do you have to wait until it’s cured, Or can you pull it wet?

I have the motor in and running. Sounds and runs good till I shut it off and restart it. Give me a p011 advance timing code. Checked everything timing good and 3 vvvts still no fixed

You are a life saver!! Thank you so much!!

Dude!! This worked!! Thanks!

Thanks

If its the om 642 they have the little flaps in Europe too.

Go on home baby 😅😂

Dude u olace the bolt on the les dense area

Purchased a water pump from my local napa with a lifetime warranty. Less than one year later it goes out and and napa can’t find it in their system that I ever bought it. They “Looked deeper “ and said “we have not sold that pump in over 2 years” I then showed the receipt and got my replacement. Just goes to show you how they will treat you if they can get away with it.

Bro you forgot to clean out that pcv orofice! Lol

Worked just as you said. Thank you.

Niagara Canada here I got two of them bastards to deal with lines rotten and broke at the fittings 🤬

The way I get a stuck bolt or nut out is to use a chisel and put it down in the socket and hammer it out

THANK YOU. 2005 Mazda Tribute (Ford Escape), Air was not coming out of the vents but blower motor was clearly running. Watched your video, looked under the hood and a vacuum line was broken. I held the pieces together, the air switched from defrost to vent. You just saved me a lot of money, all I have to do is replace some rubber lines

But can we upgrade lower control arm so we can use struts?

It doesn't make sense that Ford did it like this

Anyone know how to fix a 2007 Nissan Maranno tailgate that won't open? I can physically open it from the inside the handle is also broken but it has a little leaver I can use to open it but the outside button isn't working.

Hang in there on the Stem Cells Patches- Incredible things are happening with them! God Bless you and your family!

What a stud...no bull just actual help. Thanks for the effort.

That is not the drain plug you pointed to. That is the check level fill plug. The drain plug is under the car not on the side of the pan. Why teach people wrong? Fix the video.

Thanks for the video! I just did this on a 2000 base Impala. This video was probably the most helpful one. Here’s some thoughts while it’s still fresh in my mind. 1. There’s an electric connector that goes into the cylinder that was really hard to remove, since the cylinder won’t come out. Not in this video. I ordered a new connector off eBay because I bodged it up. Still worked as is though. 2. The key programming process, I would put the key in, go just past start enough to trigger the flashing security screen. It would flash security for 6 times then one battery, repeat for ten minutes. You could tell the ten minutes were up because it would do like one flash instead of 6. One time I didn’t turn it far enough and it just flashed one security and one battery. When it was done with all the programming, it just showed battery. 3. I did it at night but didn’t account for the headlights wanting to come on. So if you have a low battery don’t do it at night.

I am a bit challenged. I enjoy your tips and your pep sayings. So did you just continue manually turning the humonic balancer which then the belt then went into place. Stay well and cool

Hypothetically how would one discharge a Car AC unit safety to change some ac parts that need to be changed ? In my scenario, I don’t have a container to accept the refrigerant.

Man.. This is driving me nuts, tried the gasket that came with the pan, still had a leak, took off the gasket and used rtv black… about an hour later there is a new spot in the driveway. Any help would be greatly appreciated. I followed all the steps in this video including making sure to add sealer to the one bolt.

Cool. I was gonna pick this up on sale for 50. Is there a particular can tap you recommend?

2004 Silverado is different

Btw he list your vehicle in the description

Definitely much better than most of the videos that are on UA-cam about this. So many want to talk about the harness and all the crap not needed. I am only replacing a timing cover because the tensioner blew a hole in it.. Thanks for being good at what ya do and sharing your experience! For that I have subscribed!

Hey man can you please tell me if a transmission out of 2003 Yukon 4wh drive will fit in a 1997 gmc sierra 4wh drive truck w 4160 transmission?

Great fix great video. Subbed and thumbs

Awesome video, have to take my engine out after camshaft sprocket broke and bent the valves😢. This video certainly will help. Subscribed 👍🏼

Hey man you made a total error, you said that if a brake booster is bad that it won't cause spongy brakes. That's fucking wrong. They will cause spongy brakes if the brake booster is bad.. on my brake booster the rod that pushes into the master cylinder you can just pull it right out of the booster. Bought a new master cylinder bench bled it put it in no fluid comes out of any of the bleed screws which I replaced a few years ago and there's no rust underneath my vehicle like there is on yours so what the fuck

Thank you so much, I just had to change my first tyre ever and if I hadn’t come across your video I’d still be stuck. Thank you 1000 times!!!!

Can i do this to a dodge caliber 2011

Simple ???